Modification of Asymmetric Polysulfone Membrane Surfaces using Mixed Ar/O2 Plasma Technique

Chaiporn KAEW-ON; Thawat CHITTRAKARN; Soraya RUANGDIT; Chalad YUENYAO; Yutthana TIRAWANICHAKUL

doi:10.48048/wjst.2019.4773

Authors

Chaiporn KAEW-ON Faculty of Science, Department of Physics, Prince of Songkla University, Songkhla 90112
Thawat CHITTRAKARN Membrane Science and Technology Research Center, Prince of Songkla University, Songkhla 90112
Soraya RUANGDIT Membrane Science and Technology Research Center, Prince of Songkla University, Songkhla 90112
Chalad YUENYAO Department of Physics, Faculty of Science and Technology, Phetchabun Rajabhat University, Phetchabun 67000
Yutthana TIRAWANICHAKUL Faculty of Science, Department of Physics, Prince of Songkla University, Songkhla 90112

DOI:

https://doi.org/10.48048/wjst.2019.4773

Keywords:

Coagulation bath temperature, evaporation time, membrane wettability, plasma discharge, surface modification

Abstract

Asymmetric polysulfone (PSF) membranes for gas separation were prepared via dry-wet phase inversion technique at different conditions such as coagulation bath temperature (CBT) and evaporation time (ET). The thickness of the dense layer that plays an important role on gas selectivity has been investigated by adjusting CBT and ET. Additionally, membranes were treated with mixed Ar/O₂ DC glow discharge plasma in order to modify membrane wettability, surface roughness, and functional groups on the membrane surface. Scanning electron microscopy (SEM) was used to illustrate a cross sectional structure of PSF membranes. Hydrophilic properties of the membrane surfaces were analyzed via water contact angle (WCA) and surface energy measurements. Morphological structures of membrane surfaces, roughness and creation of functional groups were analyzed both before and after plasma treatment by atomic force microscopy and Fourier transform infrared spectroscopy, respectively. Experimental results show that CBT and ET can change porous voids size of the supporting layer and the dense layer thickness underneath of the membrane surface, while a mixed Ar/O₂ gas plasma treatment can enhance hydrophilic properties of the asymmetric PSF membrane surfaces.

Downloads

Download data is not yet available.

Metrics

Metrics Loading ...

References

Y Zhang, P Song, S Fu and F Chen. Morphological structure and mechanical properties of epoxy/polysulfone/cellulose nanofiber ternary nanocomposites. Compos. Sci. Tech. 2015; 115, 66-71.

T Hwang, J Oh, W Yim, J Nam, C Bae, H Kim and K Kim. Ultrafiltration using graphene oxide surface-embedded polysulfone membranes. Sep. Purif. Tech. 2016; 166, 41-7.

E Castro Vidaurre, C Achete, F Gallo, D Garcia, R Simão and A Habert. Surface modification of polymeric materials by plasma treatment. Mater. Res. 2002; 5, 37-41.

G Guillen, Y Pan, M Li and E Hoek. Preparation and characterization of membranes formed by nonsolvent induced phase separation: A review. Ind. Eng. Chem. Res. 2011; 50, 3798-817.

M Pakizeh, S Mansoori, MP Chenar and M Namvar-Mahboub. Modification of PSf membrane nanostructure using different fabrication parameters and investigation of the CO2 separation properties of PDMS-coated PSf composite membranes. Braz. J. Chem. 2013; 30, 345-54.

S Pesek and W Koros. Aqueous quenched asymmetric polysulfone membranes prepared by dry/wet phase separation. J. Memb. Sci. 1993; 81, 71-88.

C Yuenyao, Y Tirawanichakul and T Chittrakarn. Asymmetric polysulfone gas separation membranes treated by low pressure DC glow discharge plasmas. J. Appl. Polym. Sci. 2015; 132, 42116.

C Smolders, A Reuvers, R Boom and I Wienk. Microstructures in phase-inversion membranes: Part 1 Formation of macrovoids. J. Memb. Sci. 1992; 73, 259-75.

M Steen, L Hymas, E Havey, N Capps, D Castner and E Fisher. Low temperature plasma treatment of asymmetric polysulfone membranes for permanent hydrophilic surface modification. J. Memb. Sci. 2001; 188, 97-114.

G Pozniak, I Gancarz and M Bryjak. Polysulfone membranes modified with allylamine/argon plasma. In: Proceedings of the XVI-th ARS SEPARATORIA, Borowno, Poland, p. 1-4.

D Correia, C Ribeiro, G Botelho, J Borges, C Lopes, F Vaz, S Carabineiro, A Machado and S Lanceros-Méndez. Superhydrophilic poly(l-lactic acid) electrospun membranes for biomedical applications obtained by argon and oxygen plasma treatment. Appl. Surf. Sci. 2016; 371, 74-82.

H Nagasawa, Y Yamamoto, N Tsuda, M Kanezashi, T Yoshioka and T Tsuru. Atmospheric-pressure plasma-enhanced chemical vapor deposition of microporous silica membranes for gas separation. J. Memb. Sci. 2017; 524, 644-51.

H Zhou, Y Su, X Chen, J Luo, S Tan and Y Wan. Plasma modification of substrate with poly(methylhydrosiloxane) for enhancing the interfacial stability of PDMS/PAN composite membrane. J. Memb. Sci. 2016; 520, 779-89.

A Van Deynse, P Cools, C Leys, R Morent and N De Geyter. Surface modification of polyethylene in an argon atmospheric pressure plasma jet. Surf. Coat. Tech. 2015; 276, 384-90.

K Kim, K Lee, K Cho and C Park. Surface modification of polysulfone ultrafiltration membrane by oxygen plasma treatment. J. Memb. Sci. 2002; 199, 135-45.

S Modarresi, M Soltanieh, S Mousavi and I Shabani. Effect of low-frequency oxygen plasma on polysulfone membranes for CO2/CH4 Separation. J. Appl. Polym. Sci. 2012; 124, E199-E204.

D Owens and R Wendt. Estimation of the surface free energy of polymers. J. Appl. Polym. Sci. 1969; 13, 1741-7.

S Konruang, S Sirijarukul, P Wanichapichart, L Yu and T Chittrakarn. Ultraviolet-ray treatment of polysulfone membranes on the O2/N2 and CO2/CH4 separation performance. J. Appl. Polym. Sci. 2015; 132, 42074.